Getting Familiar with Plumbing: Your Starting Point for When Installing a Bathtub
Booking PageWe have encountered this article relating to How to Install a Bathtub Yourself down the page on the internet and concluded it made sense to talk about it with you here.
Installing a tub isn't specifically brain surgery, but it does call for strong plumbing, carpentry, and also occasionally, tiling abilities. Replacing an old tub with a brand-new one is also a reasonably challenging project. If the old bathtub is easily easily accessible, the task can relocate speedily; if you have to open a wall surface to get rid of the old tub and place the brand-new bathtub, the job is much harder. In either case, the job is within a home handyman's abilities, although you will require a helper to move out the old bathtub and embeded in the new one. Make certain you have certified yourself for the task and are comfortable attempting it. Instead of hiring a specialist to take control of a halfway-completed project, it is much better to take into consideration using one prior to you start. Chances are you may need a professional plumber to make tube connections.
This short article will help you install a new bathtub in your shower room if you have actually already bought a brand-new tub as well as do not need to transform the plan of your previous water supply pipes.
Your tools and material checklist must make up the following:
Removing Old Taps
If you need to replace old faucets with brand-new ones as a part of your installation, then the first thing you should do is disconnect the water system. After doing so, switch on the taps to drain pipes any kind of water staying in the system. The process of removing the existing taps can be fairly troublesome because of the restricted accessibility that is commonly the instance.
Utilize a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipelines to the taps. Have a cloth all set for the continuing to be water that will certainly come from the pipelines. As soon as the supply pipes have been gotten rid of, utilize the very same device to loosen the nut that holds the taps onto the bath/basin. You will need to quit the solitary taps from turning during this procedure. As soon as the faucets have actually been removed, the holes in the bath/basin will need to be cleaned of any kind of old securing compound.
Prior to going on to fit the brand-new faucets, compare the pipeline links on the old taps to the new taps. If the old taps are longer than the brand-new taps, then a shank adapter is required for the brand-new faucets to fit.
Fitting New Touches
If the tails of the brand-new taps are plastic, after that you will require a plastic port to stop damage to the thread. One end of the port fits on the plastic tail of the tap as well as the other end gives a connection to the existent supply pipelines.
If you need to fit a monobloc, then you will certainly require minimizing couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next, position the faucet in the mounting hole in the bath/basin making certain that the washing machines are in place between the faucet and also the sink. Secure the tap in place with the maker given backnut. As soon as the faucet is safely in position, the supply pipes can be linked to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with regular tap ports. The former kind must be linked to the faucet finishes first, tightening up only by hand. The supply pipes can later be connected to the other end. Tighten up both ends with a spanner after both ends have actually been attached.
Mounting the Tub
Using both wooden boards under its feet, position the tub in the required setting. The wooden boards are helpful in uniformly spreading the weight of the tub over the location of the boards rather than concentrating all the weight onto four little factors.
The next objective is to make certain that the bathtub is leveled all round. This can be attained by examining the spirit level as well as readjusting the feet on the bath tub until the spirit level checks out degree.
To mount faucets, fit the bottom of the furthest flexible tap port to the proper supply pipeline by making a compression sign up with; after that do the very same for the various other faucet.
Turn on the water supply and also examine all joints and also brand-new pipework for leaks and also tighten them if needed. Fill the bath tub as well as additionally examine the overflow electrical outlet as well as the normal electrical outlet for leakages.
Ultimately, repair the bathroom paneling as defined in the supplier's instruction manual. Tiling as well as securing around the bath tub should wait up until the bathtub has actually been made use of at least once as this will settle it into its final setting.
Getting ready for the Installation
To start with, the supporting framework provided with the bath needs to be fitted (if required) according to the maker's instructions. Next, fit the faucets or mixer to the bath tub. When fitting the tap block, it is important to ensure that if the faucet comes with a plastic washer, it is fitted in between the bathroom and also the faucets. On a plastic bath, it is also sensible to fit a supporting plate under the taps system to avoid stress on the tub.
Fit the versatile faucet ports to the bottom of the two taps using 2 nuts and olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the outlet through the hole in the bath. Make use of the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make sure you use all of the provided washers.
Connect the catch to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Connect all-time low of the overflow tube in a similar manner.The bath need to currently prepare to be fitted in its final setting.
Tiling Around the Bath tub
In the area where the bath satisfies the ceramic tile, it is necessary to seal the joins with a silicone rubber caulking. This is very important as the installation can relocate sufficient to fracture an inflexible seal, creating the water to penetrate the wall between the bathroom and also the tiling, resulting in problems with moisture and possible leakages to the ceiling listed below.
You can select from a range of coloured sealants to assimilate your components as well as fittings. They are marketed in tubes as well as cartridges, and can sealing gaps approximately a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with spins of drenched newspaper or soft rope. Keep in mind to always fill the tub with water before securing, to allow for the motion experienced when the tub remains in usage. The sealant can fracture relatively early if you do not take into consideration this motion before sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are likewise conveniently available on the market. It is a good idea to fit the floor tiles using water-resistant or water-proof glue and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I am very enthusiastic about Installing A Bathtub and I really hope you enjoyed the entire blog post. Sharing is caring. You just don't know, you will be doing someone a favor. Thanks a lot for your time. Please pay a visit to our site back soon.
Expert care? Call.